kool blog

o vSphere supports a maximum of eight simultaneous VMotion, cloning, deployment, or Storage VMotion accesses to a single VMFS3
datastore, and a maximum of four simultaneous VMotion, cloning, deployment, or Storage VMotion accesses to a single NFS or VMFS2 220 702
datastore. A migration with VMotion involves one access to the datastore. A migration with Storage VMotion involves one access to the
source datastore and one access to the destination datastore
o Disks are converted from thin to thick format or thick to thin format only when they are copied from one datastore to another. If you choose
to leave a disk in its original location, the disk format is not converted.
o Thin or thick provisioned – not available for RDMs in physical compatibility mode. If you select this option for a virtual compatibility mode
RDM, the RDM is converted to a virtual disk. RDMs converted to virtual disks cannot be converted back to RDMs.
o You can run the storage vmotion command in either interactive or noninteractive mode.
o Interactive mode, type svmotion –interactive.
o Noninteractive mode: svmotion [Standard CLI options] –datacenter= –vm ‘:’ [–disks ‘:, :]’
o A snapshot captures the entire state of the VM at the time you take the snapshot. This includes:
o Memory state – The contents of the VM’s memory.
o Settings state – The VM settings.
o Disk state – The state of all the VM’s virtual disks.
o Snapshots of raw disks, RDM physical mode disks, and independent disks are not supported.
o Change Disk Mode to independent to Exclude Virtual Disks from Snapshots
o Persistent – Disks in persistent mode behave like conventional disks on your physical computer. All data written to a disk in persistent mode
are written permanently to the disk.
o Nonpersistent – Changes are discarded when you power off or reset the VM. Nonpersistent mode enables you to restart the VM with a virtual
disk in the same state every time. Changes to the disk are actually written to and read from a redo log file that is deleted when you power off 9L0-403
or reset.
o Snapshots:
o Delete – commits the snapshot data to the parent and removes the selected snapshot.
o Delete All – commits all the immediate snapshots before the You are here current state to the base disk and removesall existing
snapshots for that VM.
o Revert to Snapshot – a shortcut to the parent snapshot of “You are here”.
o If you use Active Directory groups for permissions, make sure that they are security groups and not distribution groups.
o Users who are currently logged in and are removed from the domain retain their vSphere permissions only until the next validation period (the
default is every 24 hours).
o A role is a predefined set of privileges. Privileges define basic individual rights required to perform actions and read properties. When you
assign a user or group permissions, you pair the user or group with a role and associate that pairing with an inventory object.
o Default roles:
o System roles – System roles are permanent. You cannot edit the privileges associated with these roles.
o Sample roles – VMware provides sample roles for convenience as guidelines and suggestions. You can modify or remove these roles.
o You can also create completely new roles.
o All roles permit the user to schedule tasks by default. Users can schedule only tasks they have permission to perform at the time the tasks are
created.
o Default roles:
Role Role Type Description of User Capabilities
No Access system Cannot view or change the assigned object. available in ESX/ESXi and vCenter Server.
Read Only system View the state and details about the object. available on ESX/ESXi and vCenter
Server.
Administrator system All privileges for all objects. available in ESX/ESXi and vCenter Server.
Virtual Machine
Power User
sample allow the user to interact with and make hardware changes to VMs, as well as
perform snapshot operations. available only on vCenter Server.
Virtual Machine User sample allow the user to interact with a VM’s console, insert media, and perform power
operations. available only on vCenter Server.
Resource Pool
Administrator
sample allow the user to create child resource pools and modify the configuration of the
children, but not to modify the resource configuration of the pool or cluster on which
the role was granted. Also allows the user to grant permissions to child resource
pools, and assign VMs to the parent or child resource pools. available only on
vCenter Server.
VMware Consolidated 9L0-510
Backup User
sample used by the VMware Consolidated Backup product and should not be modified.
available only on vCenter Server.
Datastore Consumer sample allow the user to consume space on the datastores on which this role is granted.
available only on vCenter Server.
Network Consumer sample allow the user to assign VMs or hosts to networks available only on vCenter Server.

o NPIV support is subject to the following limitations:
o NPIV must be enabled on the SAN switch.
o NPIV is supported only for VMs with RDM disks.
o The physical HBAs on the ESX host must have access to a LUN using its WWNs in order for any VMs on that host to have access to that 220 701
LUN using their NPIV WWNs.
o The physical HBAs on the ESX host must support NPIV.
o Each VMcan have up to 4 virtual ports. NPIV-enabled VMs are assigned exactly 4 NPIV-related WWNs. Can utilize up to 4 physical HBAs
for NPIV purposes.
o A VM with WWNs that are already in use on the storage network is prevented from powering on.
o While hyperthreading does not double the performance of a system, it can increase performance by better utilizing idle resources.
o The advanced CPU settings are useful only for fine-grained tweaking of critical VMs.
o NUMA memory node affinity enables fine-grained control over how VM memory is distributed to host physical memory.
o Specify nodes to be used for future memory allocations only if you have also specified CPU affinity.
o The following NIC types are supported:
vNIC Description
Flexible Supported on VMs that were created on ESX Server 3.0 or greater and that run 32-bit guest operating systems.
The Flexible adapter functions as a vlance adapter if VMware Tools is not installed in the VM and as a vmxnet
driver if VMware Tools is installed in the VM.
e1000 Emulates the functioning of an E1000 network card. It is the default adapter type for VMs that run 64-bit guest
operating systems.
Enhanced vmxnet An upgraded version of the vmxnet device with enhanced performance. It requires that VMware Tools be
installed in the VM. 220 702
vmxnet 3 Next generation vmxnet device with enhanced performance and enhanced networking features. It requires that
VMware Tools be installed in the VM, and is available only on VMs with hardware version 7 and greater.
o Independent disks are not affected by snapshots.
o Two modes for independent disks:
o Persistent – The disk operates normally except that changes to the disk are permanent even if the VM is reverted to a snapshot.
o Nonpersistent – The disk appears to operate normally, but whenever the VM is powered off or reverted to a snapshot, the contents of
the disk return to their original state. All later changes are discarded.
o VMDirectPath I/O allows a guest operating system on a VM to directly access physical PCI and PCIe devices connected to a host. Each VM can
be connected to up to two PCI devices. PCI devices connected to a host can be marked as available for passthrough from the Hardware
Advanced Settings in the Configuration tab for the host.
o Paravirtual SCSI (PVSCSI) adapters are high-performance storage adapters that can provide greater throughput and lower CPU utilization.
PVSCSI adapters are best suited for environments, especially SAN environments, running I/O-intensive applications. PVSCSI adapters are not
suited for DAS environments.
o Hardware requirements for customizing the guest operating system:
o Must reside on a disk attached as SCSI 0:0 node in the VM configuration.
o If a VM has mixed IDE and SCSI disks, the first IDE disk is considered the boot disk, and vCenter Server passes it to the customizer.
o If the new VM encounters customization errors while it is booting
o Customization errors are logged to (Windows guest) %WINDIR%\temp\vmware-imc or (Linux guest) /var/log/vmware/customization.log.
o When you migrate a suspended VM, the new host for the VM must meet CPU compatibility requirements, because the VM must resume
executing instructions on the new host.
o Use of Jumbo Frames is recommended for best VMotion performance.
o Some restrictions apply when migrating VMs with snapshots. You cannot migrate a virtual machine with snapshots with Storage VMotion.
o You can migrate as long as the VM is being migrated to a new host without moving its configuration file or disks (the VM must reside on
shared storage accessible to both hosts).
o Reverting to a snapshot after migration with VMotion might cause the VM to fail, because the migration wizard cannot verify the compatibility
of the VM state in the snapshot with the destination host.
o During a migration with Storage VMotion, you can transform virtual disks from thick-provisioned to thin or from thin-provisioned to thick. 220 701
o Storage VMotion is subject to the following requirements and limitations:
o Virtual machines with snapshots cannot be migrated using Storage VMotion.
o Virtual machine disks must be in persistent mode or be raw device mappings (RDMs). For virtual compatibility mode RDMs, you can
migrate the mapping file or convert to thick-provisioned or thinprovisioned disks during migration as long as the destination is not an NFS
datastore. For physical compatibility mode RDMs, you can migrate the mapping file only.
o Must have a license that includes Storage VMotion.
o ESX/ESXi 3.5 hosts must be licensed and configured for VMotion. ESX/ESXi 4.0 and later hosts do not require VMotion configuration in
order to perform migration with Storage VMotion.
o A particular host can be involved in up to two migrations with VMotion or Storage VMotion at one time.

o The vSphere Client validates an OVF file before importing it.
o A vApp is a container, like a resource pool and can contain one or more VMs. A vApp can power on and power off, and can also be cloned.
o The vApp metadata resides in the vCenter Server’s database
o You can add an object, such as a VM or another vApp, to an existing vApp.
o An IP pool is a network configuration that is assigned to a network used by a vApp. The vApp can then leverage vCenter Server to 640 802 Dumps
automatically provide an IP configuration to its VMs.
o Each application within the service will be powered on according to how the startup order is set. When powering on a vApp within a DRS
cluster in manual mode, no DRS recommendations are generated for VM placements. The power on operation performs as if DRS is run in a
semi-automatic or automatic mode for the initial placements of the VMs. This does not affect VMotion recommendations. Recommendations
for individual powering on and powering off of VMs are also generated for vApps that are running
o A VM’s name can be up to 80 characters long. Names are case insensitive.
o Virtual machine version 4 — Compatible with ESX 3.0 and greater hosts and VMware Server 1.0 and greater hosts.
o Virtual machine version 7 — Compatible with ESX 4.0 and greater hosts. Provides greater VM functionality.
o Paravirtual SCSI (PVSCSI) adapters are high-performance storage adapters that can result in greater throughput and lower CPU utilization.
o Best suited for high performance storage environments.
o Not suited for DAS environments. VMware recommends that you create a primary adapter (LSI Logic by default) for use with a disk that
will host the system software (boot disk) and a separate PVSCSI adapter for the disk that will store user data, such as a database.
o Paravirtual SCSI adapters are available for VMs running hardware version 7 and greater. They are supported on the following guest operating
systems:
o Windows Server 2008
o Windows Server 2003
o Red Hat Linux (RHEL) 5
o Features not supported with Paravirtual SCSI adapters:
o Boot disks
o Record/Replay
o Fault Tolerance
o MSCS Clustering
o SCSI controller types:
o BusLogic Parallel
o LSI Logic SAS
o LSI Logic Parallel
o VMware Paravirtual
o Thin Provisioned Format – Use this format to save storage space. If a virtual disk supports clustering solutions such as Fault Tolerance, you
cannot make the disk thin. You can manually convert the thin disk into thick.
o Thick Format – This is the default virtual disk format. It is not possible to convert the thick disk into thin. (EDIT: you can via Storage VMotion) 640-802</a
o Automatic VMware Tools upgrade is not supported for VMs with Solaris or Netware guest operating systems.
o If you are using a WYSE thin client device to conduct remote desktop sessions using VMware VDI, installing WYSE Multimedia Support in the
guest operating system improves the performance of streaming video. WYSE Multimedia Support is supported on the Windows 2003 and
Windows XP guest operating systems only. WYSE Multimedia Support is installed as part of a VMware Tools installation or upgrade.
o Virtual machines with hardware versions lower than 4 can run on ESX4 hosts but have reduced performance and capabilities. In particular, you
cannot add or remove virtual devices on VMs with hardware versions lower than 4 when they reside on an ESX4 host.
o Virtual Machine Hardware Versions:
Host Version 7 Version 4 Version 3 Compatible with vCenter Server version
ESX/ESXi 4.x create, edit, run create, edit, run run vCenter Server 4.x
ESX Server 3.x – create, edit, run run VirtualCenter Server 2.x and higher
ESX Server 2.x – – create, edit, run VirtualCenter Server 1.x and higher
o SCSI Bus Sharing list:
Option Description
None Virtual disks cannot be shared by other VMs.
Virtual Virtual disks can be shared by VMs on same server.
Physical Virtual disks can be shared by VMs on any server.
o Memory/CPU Hotplug – VMware Tools must be installed for hotplug functionality to work properly.
o VMI – A paravirtualization standard that enables improved performance for VMs capable of utilizing it.
o Enabling paravirtualization utilizes one of the VM’s six virtual PCI slots
o A VM with paravirtualization enabled and that is powered off can be moved manually to a host that does not support paravirtualization. 640 802 braindumps
However, this can result in reduced performance.
o N-port ID virtualization (NPIV) – Provides the ability to share a single physical Fibre Channel HBA port among multiple virtual ports, each with
unique identifiers. This allows control over VMaccess to LUNs on a per-VMbasis.

o ESX/ESXi System Logs
Component Location
ESX Server 2.x Service log /var/log/vmware/vmware-serverd.log
ESX Server 3.x or ESX Service log /var/log/vmware/hostd.log
vSphere Client Agent log /var/log/vmware/vpx/vpxa.log
Virtual Machine Kernel Core file /root/vmkernel-core. and /root/vmkernel-log. present after rebooting
Syslog log /var/log/messages
Service Console Availability report /var/log/vmkernel
VMkernel Messages /var/log/vmkernel
VMkernel Alerts & Availability report /var/log/vmkernel
VMkernel Warning /var/log/vmkwarning
Virtual Machine log file The same directory as the .vmx file for the VM.
o vSphere Client System Logs vcp 4
Component Location
vSphere Client Installation log Temp directory on the vSphere Client machine. e.g.: C:\Documents and Settings\\Local Settings\Temp\vmmsi.log
vSphere Client Service log \vpx directory in the Application Data directory on the vSphere Client machine. e.g.:
C:\Documents and Settings\\Local Settings\Application Data \vpx\viclientx.
log x(=0, 1, … 9)
o VMware Server System Logs
Component Operating System Location
VM Console log Windows Temp directory e.g.: C:\Documents and Settings\\Local Settings
\Temp\vmware–.log
Linux Temp directory e.g.: /tmp/vmware-/ui-.log
VM log Windows & Linux vmware.log Located in the same directory as the VM .vmx file.
VM Event log Windows C:\Program Files\VMware\VMware Virtual Infrastructure\
vmserverdRoot\eventlog\vent- .vmx.log
Linux /var/log/vmware/event-.vmx.log
VM Conf file Windows .vmx Located in the folder where VMs are stored.
Linux .vmx Located in the folder where VMs are stored.
o All ESX/ESXi hosts run a syslog service (syslogd).
o ESXi hosts can use the vSphere Client or the vSphere CLI command vicfg-syslog
o Cannot use the vSphere Client or vicfg-syslog to configure syslog behavior for an ESX host. To configure syslog for an ESX host, you must
edit the /etc/syslog.conf file.
o Libraries – Central repositories for VM provisioning media e.g. VM templates, ISO images, floppy images, VMDK files, guest customization files.
o Guided Consolidation ports
Port Protocol Service Description MS Windows
135 TCP/UDP Loc-srv/epmap Microsoft DCE Locator service (End-point Mapper). DHCP, DNS & WINS Server
137 TCP/UDP Netbios-ns NetBIOS names service. WINS & DNS Server
138 TCP/UDP Netbios-dgm NetBIOS datagram vmware vcp 4
139 TCP/UDP Netbios-ssn NetBIOS Session Windows File and Printer sharing.
445 TCP/UDP DNS DNS Direct Hosting port. Active Directory
o Guided Consolidation can be installed together with vCenter Server, or can be installed on a separate host. For best performance, install
Guided Consolidation on a separate host. It includes the following services:
o vCenter Collector Service – Discovers domains and systems within domains. Collects performance data on those systems.
o vCenter Provider Service – Helper service to the Collector Service. Communicates with target systems and passes the data back.
o vCenter Guided Consolidation – Coordinates all communication among Guided Consolidation components.
o You can analyze up to 100 systems simultaneously.
o The following formula is used to resize converted disks:
o amount of space used on physical disk * 1.25 = resultant virtual disk size
o Virtual disks are set to a size of 4GB or larger.
o Disconnecting a managed host does not remove it from vCenter Server; it temporarily suspends all monitoring activities performed by vCenter
Server. 640 802
o Deploying an OVF template is similar to deploying a VM from a template. However, you can deploy an OVF template from any local file system
accessible from the vSphere Client machine, or from a remote web server.
o OVF advantages:
o OVF files are compressed, allowing for faster downloads.

o Performance charts
o WebAccess
o vCenter Storage Monitoring/Storage Views tab
o vCenter Service Status
o When a server is connected to other vCenter Server systems using Linked Mode, you can connect to that vCenter Server system and view and
manage the inventories of all the vCenter Server systems that are linked.
o Linked Mode uses Microsoft Active Directory Application Mode (ADAM) to store and synchronize data.
o The following requirements apply to each vCenter Server system that is a member of a Linked Mode group:
o DNS must be operational.
o Can be in different domains if the domains have a two-way trust relationship.
o When adding a vCenter instance to a Linked Mode group, the installer must be run by a domain user who is an administrator on both the
machines. vcp-410
o Must have network time synchronization. The installer validates that the machine clocks are not more than 5 minutes apart.
o The roles defined on each vCenter Server system in a linked mode group are replicated to the other systems in the group.
o Troubleshooting:
o Conflicts can occur, when you clone a vCenter Server instance that is running in a VM and you do not use sysprep or a similar utility to
ensure that the cloned vCenter Server instance has a globally unique identifier (GUID).
o The DNS name of the machine must match with the actual machine name.
o Joining a Linked Mode group:
1. Verify that the vCenter Server domain name matches the machine name.
2. Update the URLs to make them compatible with the new domain name and machine name (if required).
3. Join the vCenter Server system to a Linked Mode group.
o When you are logged in to a vCenter Server system that is part of a connected group, you can monitor the health of services running on each
server in the group.
o Client uses ports 80 and 443 to communicate with vCenter Server and ESX/ESXi hosts. These ports cannot be changed.
o The SNMP traps sent by vCenter Server are defined in VMWARE-VC-EVENT-MIB.mib
o ESX/ESXi includes an SNMP agent embedded in hostd that can both send traps and receive polling requests such as GET requests. This agent is
referred to as the embedded SNMP agent. Versions of ESX prior to ESX 4.0 included a Net-SNMP-based agent. You can continue to use this
Net-SNMPbased agent in ESX 4.0 with MIBs supplied by your hardware vendor and other third-party management applications. However, to
use the VMware MIB files, you must use the embedded SNMP agent. By default, the embedded SNMP agent is disabled. To enable it, use the
vSphere CLI command vicfg-snmp.
o Both the embedded SNMP agent and the Net-SNMP-based agent available in the ESX service console listen on UDP port 161 by default. If you vmware vcp 410
enable both of these agents for polling on an ESX host, you must change the port used by at least one of them.
o Can use SNMP to monitor guest operating systems or applications running in VMs. Do not install agents in the VM that are intended to
monitor physical hardware.
o VMware MIB Files
MIB File Description
VMWARE-ROOT-MIB.mib Contains VMware’s enterprise OID and top level OID assignments.
VMWARE-AGENTCAP-MIB.mib Defines the capabilities of the VMware agents by product versions.
VMWARE-ENV-MIB.mib Defines variables and trap types used to report on the state of physical hardware components of
the host computer.
VMWARE-OBSOLETE-MIB.mib Defines OIDs that have been made obsolete to maintain backward compatibility with earlier
versions of ESX/ESXi. Includes variables formerly defined in the files VMWARE-TRAPS-MIB.mib
and VMWARE-VMKERNEL-MIB.mib.
VMWARE-PRODUCTS-MIB.mib Defines OIDs to uniquely identify each SNMP agent on each VMware platform by name, version,
and build platform.
VMWARE-RESOURCES-MIB.mib Defines variables used to report information on resource usage of the VMkernel, including
physical memory, CPU, and disk utilization.
VMWARE-SYSTEM-MIB.mib The VMWARE-SYSTEM-MIB.mib file is obsolete. Use the SNMPv2-MIB to obtain information
from sysDescr.0 and sysObjec ID.0. vmware vcp 4
VMWARE-TC-MIB.mib Defines common textual conventions used by VMware MIB files.
VMWARE-VC-EVENTS-MIB.mib Defines traps sent by vCenter Server. Load this file if you use vCenter Server to send traps.
VMWARE-VMINFO-MIB.mib Defines variables for reporting information about VMs, including VM traps.

o After you upgrade all of your hosts to ESX4/ESXi4, you can optionally uninstall your license server and remove the license server configuration
from vCenter Server.
o For ESXi, the vSphere Host Update Utility does not support roll back.
o You can remove the ESX 4.0 boot option from the ESX bootloader menu and perform a complete roll back to ESX 3.x. Any changes made to Passed VCP410
the ESX 4.0 service console are lost after the rollback.
o Any changes made to VMs will persist after the rollback.
o If you upgraded the VM hardware, the VMs will not work after you perform the ESX rollback. To avoid this situation, take a snapshot of
the VM before you upgrade the VM hardware.
o Run the rollback-to-esx3 command – reconfigures the bootloader.
o Reboot the server.
o After the host boots into ESX 3.x, delete the ESX 4.0 service console VMDK folder from the VMFS datastore.
o Each time you update an ESXi host, a copy of the ESXi build is saved on your host.
o ESXi permits only one level of rollback.
o When you manually boot into the standby build instead of the current boot build, an irreversible rollback occurs.
o When the page that displays the current boot build appears, press Shift+r to select the standby build.
o Do not use vmware-vmupgrade.exe to upgrade VMs.
o Some VMs that you create on ESX4 hosts are supported on ESX 3.x/ESXi 3.5 hosts. If you create a VM on ESX4 and select the typical path, the
virtual hardware version is version 7. Virtual machines with virtual hardware version 7 are not supported on ESX 3.x/ESXi 3.5 hosts. Select the
custom path and select virtual hardware version 4
o If you create VMs that use paravirtualization (VMI) or an enhanced networking device (vmxnet), VMotion is not supported. In this case, you
can only move the VM to the ESX 3.x host if the VM is powered off.
o On Windows guest operating systems, you must reboot the VM a total of three times when you upgrade VMware Tools and the virtual
hardware: Passed VCP 4
1. Power on the VM.
2. Upgrade VMware Tools.
3. Reboot the VM at the end of the VMware Tools upgrade.
4. Power off the VM.
5. Upgrade the virtual Hardware.
6. Power on the VM.
7. The Windows operating system detects new devices and prompts you to reboot the VM.
8. Reboot the VM to make the devices work properly.
o During the virtual hardware upgrade, the VM must be shut down for all guest operating systems.
o When you upgrade from virtual hardware version 3 to version 7, the upgrade is irreversible, even if you take a VM backup or snapshot before
performing the upgrade. 4 to version 7 the upgrade is reversible if you take a VM backup or snapshot
o Tools for installing updates and patches to ESX/ESXi hosts:
o Host Update Utility – graphical utility for ESXi only.
o Update Manager – for ESX and ESXi,
o vihostupdate – command-line utility for ESX and ESXi.
o esxupdate – command-line utility for ESX only.
o If the Host Update Utility does not meet the needs of your environment, you can customize the application the settings.config XML file,
located in %PROGRAMFILES%\VMware\Infrastructure\VIUpdate 4.0
o Run vihostupdate on ESX 4.0/ESXi 4.0 hosts. Run vihostupdate35 on ESX 3.5/ESXi 3.5 hosts.
o The esxupdate utility is supported as well. It is for ESX only.
o The vihostupdate command works with bulletins.
o You can use the vihostupdate utility in conjunction with offline bundles or with a depot.
o To get the build number of an ESX4 host: # vmware –l (from KB 1001179).
vSphere Basic System Administration
o VMware modules (plugins) include:
o Update Manager
o Converter Enterprise
o vShield Zones – an application-aware firewall built for vCenter Server integration. It inspects client-server communications and intervirtual-
machine communication to provide detailed traffic analytics and application-aware firewall partitioning.
o Orchestrator – a workflow engine that enables you to create and execute automated workflows.
o Data Recovery – a disk-based backup and recovery solution. Enable centralized and efficient management of backup jobs and includes
data de-duplication. vcp 410
o Tomcat Web server is installed as part of the vCenter Server installation. The components that require Tomcat are:
o Linked Mode
o CIM/Hardware Status tab

o Back up the VirtualCenter 2.x SSL certificates. %ALLUSERSPROFILE%\Application Data\VMware\VMware VirtualCenter or
%ALLUSERSPROFILE%\VMware\VMware VirtualCenter\.
o Note any non-default settings, such as the IP address, the database DSN, user name, password, and assigned ports.
o Create a backup copy of vpxd.cfg.
o The database upgrade log is at %TEMP%\VCDatabaseUpgrade.log.
o By default, a vCenter Server creates VCP-410 questions a maximum of 10 simultaneous database connections.
o Datastores and networks have their own set of privileges that control access to them.
o Users are initially granted the No Access role on all new managed objects, including datastores and networks. All existing objects in vCenter
maintain their permissions after the upgrade.
o The upgrade process uses the datacenter’s “Read-only” privilege.
o If the “Read-only” privilege is nonpropagating (not inherited by child objects), VMware assumes access privileges should not be assigned
to datastores and networks.
o If the “Read-only” privilege is propagating (inherited by child objects), VMware assumes access privileges should be assigned to
datastores and networks so users can view them and perform basic operations that require access.
o The “Read-only” propagating permission on a datacenter, as well as all other permissions you have set, will continue to work as expected after
the upgrade.
o You must change “Read-only” nonpropagating datastore permissions to propagating datastore permissions in order for users to access the
datastore. You can assign datastore permissions on datastore or folders containing datastore. The same goes for Network permissions.
o The “Database Consumer” sample role assigns the “Allocate Space” privilege to the datastore. “Network Consumer” sample role assigns the
“Assign Network” privilege.
o Host Update Utility does not upgrade VMFS datastores or VM
o Update Manager supports mass remediation.
o During host upgrades using the Update Manager, static IP addresses are a requirement.
o The upgrade to ESXi4 & ESX4 preserves almost all configuration data, including your networking, security, and storage configuration. The only
configuration not preserved is related to licensing.
o For ESX only, the upgrade reuses the existing /boot partition to hold the ESX 4.0 boot files. After the upgrade, the ESX 3.x installation is VCP-410 dumps
mounted in the new ESX 4.0 installation under the /esx3-installation directory.
o Backup the ESX Host Configuration:
o Back up the files in the /etc/passwd, /etc/groups, /etc/shadow, and /etc/gshadow directories.
o Back up any custom scripts.
o Back up your .vmx files.
o Back up local images, such as templates, exported VMs, and .iso files.
o Backup the ESXi Host Configuration: vicfg-cfgbackup –server –portnumber –
protocol –username username –password -s
o You cannot perform an in-place upgrade from ESX to ESXi (or from ESXi to ESX).
o The only ESX 2.x version that has upgrade support is ESX 2.5.5 – you can perform a migration upgrade with or without VMotion.
o Direct, in-place upgrade from ESX 2.5.5 to ESX 4.0 is not supported, even if you upgrade to ESX 3.x as an intermediary step. The default ESX
2.5.5 installation creates a /boot partition that is too small to enable upgrades to ESX 4.0. As an exception, if you have a non-default ESX 2.5.5
installation on which at least 100MB of space is available on the /boot partition, you can upgrade ESX 2.5.5 to ESX 3.x and then to ESX 4.0.
o The upgrade logs are here:
o /esx3-installation/esx4-upgrade/
o /var/log/vmware/
o For an unsuccessful ESX upgrade:
o /esx4-upgrade/
o /var/log/vmware/
o You may need to reconnect the host to vCenter Server and assign an upgraded license to your product within 60 days after the upgrade.
o The host sdX devices might be renumbered after the upgrade.
o You must convert LUN masking to the claim rule format. Run the esxcli corestorage claimrule convert command. It converts
the /adv/Disk/MaskLUNs advanced configuration entry in esx.conf to claim rules with MASK_PATH as the plug-in.
o Web Access service is disabled after you upgrade the host. Passed VCP-410
o vSphere Web Access is not supported on ESXi hosts.
o 60-day evaluation count down starts even if the host is licensed and you are not using evaluation mode.
o One advantage of using evaluation mode is that it offers full feature functionality.
o After you determine that the ESX 4.0 upgrade is stable, you can remove the ESX 3.x boot option from the ESX 4.0 bootloader menu to disable
the ability to roll back to ESX 3.x. If you deselected the rollback option, this procedure is not applicable. Run the cleanup-esx3 command
with the optional -f (force) flag.
o The cleanup-esx3 script removes the following files and references from the ESX 4.0 host:
o ESX 3.x references in the /etc/fstab directory
o ESX 3.x boot files in the /boot directory
o The rollback-to-esx3 script in the /usr/sbin/ directory

o When you restore the standard switch, a new virtual adapter is created and the management network uplink that is currently connected to
vNetwork Distributed Switch is migrated to the new virtual switch.
o The software creates these partitions:
o One 4GB VFAT scratch partition for system swap.
o One VMFS3 partition on the remaining free space. VCP-410 exam
o The installer creates a 110MB diagnostic partition for core dumps.
o The scratch partition is not required (but created by default during the installation). It is used to store vm-support output, which you need
when you create a support bundle.
o Lockdown mode prevents remote personnel from logging in to the ESXi host by using the root login name. By default, lockdown mode is
disabled.
o Resetting the configuration does not remove virtual machines on the ESXi host. After you reset the configuration defaults, the virtual
machines are not visible, but you can retrieve them by reconfiguring storage and reregistering the virtual machines.
o When you perform a configuration backup, the serial number is backed up with the configuration and is restored when you restore the
configuration. The serial number is not preserved when you run the Recovery CD (ESXi Embedded) or perform the repair operation (ESXi
Installable).
o When you restore the configuration, the target host must be in maintenance mode, which means all virtual machines (including the vSphere
CLI virtual appliance) must be powered off.
o Run the vicfg-cfgbackup command with the -s flag to save the host configuration to the specified backup filename.
o When you restore configuration data, the build number currently running on the host must be the same as the build number that was running
when you created the backup file. You can override this requirement by including the -f (force) flag with the vicfg-cfgbackup
command.
o Run the vicfg-cfgbackup command with the -l flag to load the host configuration from the specified backup file.
o You can restore the ESXi Installable software by running the ESXi installation CD in repair mode. All host configuration data is overwritten by VCP-410 exam questions
system defaults.
o During the repair operation, your existing ESXi 4.0 Installable VMFS datastore is preserved if it is in its original location on the ESXi 4.0 boot
disk, or if it is located on another disk (separate from the boot disk). If you changed the VMFS location on the boot disk, it is preserved if it is
located beyond the 900MB partition.
vSphere upgrade guide
o When you upgrade from ESX 3.x/ESXi 3.5 to ESX 4.0/ESXi 4.0, you can use either the vSphere Host Update Utility or vCenter Update Manager.
o EDIT – you can also use the upgrade script (esxupgrade.sh – KB 1009440). VMware doesn’t mention the option of a fresh install at any point;
they are pushing the upgrade option as much as possible. You can’t seem to do an upgrade with the ESX4 install CD.
o Host Update Utility is used for upgrading ESX 3.x/ESXi 3.5 standalone hosts to ESX 4.0/ESXi 4.0 and for patching ESXi 4.0 standalone hosts. It is
a standalone Microsoft Windows application recommended for smaller deployments with fewer than 10 ESX/ESXi hosts, without vCenter
Server or Update Manager.
o vCenter Update Manager is for upgrading and updating ESX/ESXi hosts that are managed in vCenter Server.
o Orchestrated upgrades can be used to upgrade the VM hardware and VMware Tools.
o No VMFS upgrade is required if you are upgrading from ESX 3.x
o You must upgrade VMware Tools before upgrading virtual hardware.
o After you upgrade to vCenter Server, you cannot revert to VirtualCenter 2.x. Take appropriate backups before starting the upgrade.
o Upgrade VirtualCenter 2.x to vCenter Server 4.0:
o Make sure your database is compatible
o Have required permissions VCP-410 study guide
o Take a full backup of the VirtualCenter 2.x database
o Back up the VirtualCenter 2.x SSL certificates
o Install the vSphere Client
o vCenter Converter, upgrade
o vCenter Guided Consolidation upgrade
o Upgrade to vCenter Update Manager 4.0.
o Use vCenter Update Manager to upgrade ESX 3.x hosts to ESX 4.0. (or use host update utility)
o Use vCenter Update Manager to upgrade your VMs. vCenter Update Manager ensures that the VMware Tools upgrade and the virtual
hardware upgrade happen in the correct order
o Upgrade your product licenses
o ESX 2.x hosts cannot be added to clusters.
o Oracle 9i is no longer supported.
o Microsoft SQL Server 2000 is no longer supported.
o To Back Up VirtualCenter 2.x:
o Make a full backup of the VirtualCenter 2.x database.

o vCenter Server instances in a Linked Mode group can be in different domains if the domains have a two-way trust relationship.
o The installer must be run by a domain user who is an administrator on both the machines.
o The vCenter Server installer validates that the machine clocks are not more than 5 minutes apart.
o The instances can run under different domain accounts.
o Windows Server 2008 automatically configures the firewall to permit access. Launch firewall.cpl and add an exception for
C:\Windows\ADAM\dsamain.exe VCP-410 exam
o When you install vCenter Server in Linked Mode, the firewall configuration on any network-based firewalls must be modified.
o Configure Windows RPC ports to generically allow selective ports for machine-to-machine RPC communication.
o vCenter Collector service – uses port 8181 and 8182, by default.
o vCenter Web Server – uses ports 8080 and 8443, by default.
o All product licenses are encapsulated in 25-character license keys that you can manage and monitor from vCenter Server.
o vSphere Licenses – For ESX/ESXi.
o vCenter Server Licenses – For vCenter Server.
o vCenter Server 4.0 does not require a license server to manage ESX 4.0/ESXi 4.0 hosts. However, vCenter Server 4.0 does requires a license
server to manage ESX 3.x/ESXi 3.5 hosts.
o If a vCenter Server license expires, the managed hosts become disconnected.
o If an ESX/ESXi host license expires, the VMs that reside on the host continue to run, but you cannot power on the VMs or reset them.
ESXi Installable and vCenter Server Setup Guide
o When you power on the ESXi host for the first time or after resetting the configuration defaults, the host enters an autoconfiguration phase
during which system network and storage devices are configured with defaults.
o By default, DHCP configures IP and all visible blank internal disks are formatted with VMFS so that virtual machines can be stored on the disks.
o ESXi has an interface called the direct console to:
o Configuring host defaults
o Setting up administrative access
o Troubleshooting
o Minimum hardware configurations supported by ESXi 4.0:
o 64-bit x86 CPUs.
o 2GB RAM minimum
o Supported SATA, SAS or SCSI disks
o The installer reformats and partitions the target disk and installs the ESXi 4.0 boot image.
o ESXi Installable is always installed in evaluation mode (60 days).
o ESXi Installable and ESXi Embedded cannot exist on the same host. VCP-410 exam questions
o Booting multiple servers from a single shared ESXi image is not supported.
o If there is no DHCP available during the install, it assigns the link local IP address, which is in the subnet 169.254.x.x/16.
o Direct Console
Action Key
View and change the configuration F2
Change the user interface to high-contrast mode F4
Shut down or restart the host F12
Move the selection between fields Arrow keys
Select a menu item Enter
Toggle a value Spacebar
Confirm sensitive commands, such as resetting configuration defaults F11
Save and exit Enter
Exit without saving Esc
Exit system logs q
o To change the security banner > Advanced Settings window, select Annotations.
o Test Management Network:
o Pings the default gateway
o Pings the primary DNS nameserver
o Pings the secondary DNS nameserver
o Resolves the configured host name
o Restarting the management agents restarts all management agents and services that are installed and running in /etc/init.d on the ESXi host.
Typically, these agents include hostd, ntpd, sfcbd, slpd, wsman, and vobd. The software also restarts the Automated Availability Manager
(AAM) if it is installed. VCP-410 study guide
o Disable the management network is if you want to isolate an ESXi host from an HA and DRS cluster, but you do not want to lose your static IP
and DNS configurations or reboot the host.

o ks-first-safe.cfg Installs ESX on the first detected disk and preserves the VMFS datastores on the disk.
o ks-first.cfg Installs ESX on the first detected disk.
o The default root password is mypassword.
o /boot and vmkcore are physical partitions. /, swap, /var/log, and all the optional partitions are stored on a virtual disk called esxconsole-
/esxconsole.vmdk. The virtual disk is stored in a VMFS volume.
o You cannot define the sizes of the /boot, vmkcore, and /vmfs partitions when you use the graphical or text installation modes. You can define VCP-410 dumps
these partition sizes when you do a scripted installation.
o ESX Required Partitions
Mount Point Type Size Location
/boot ext3 1.25GB of free space and includes the /boot and vmkcore
partitions. The /boot partition alone requires
1100MB.
Physical partition
N/A swap 600MB recommended minimum 1600MB maximum. Virtual disk in a VMFS volume
/ ext3 Based on the size of the /usr partition. By default, the
minimum size is 5GB and no /usr partition is defined.
Virtual disk in a VMFS volume
N/A VMFS3 For VMFS volumes hosting esxconsole.vmdk: 1200MB and
an additional 10GB. VMFS2 is supported in read-only
mode to import legacy VMs.
Physical partition.
N/A vmkcore See /boot Physical partition
o ESX Optional Partitions
Mount Point Type Recommended Size Location
/home ext3 512MB Virtual disk in a VMFS volume
/tmp ext3 1024MB Virtual disk
/usr ext3 Missing in PDF Virtual disk
/var/log ext3 2000MB Virtual disk. The graphical and text
installers create this partition by
default.
o vihostupdate command applies software updates to ESX4/ESXi4 hosts and installs and updates ESX/ESXi extensions (use vihostupdate35 on
ESX 3.5/ESXi 3.5 hosts.) VCP-410
o The esxupdate utility is for ESX only.
o You can use the vihostupdate utility in conjunction with offline bundles or with a depot
o vSphere Databases:
o Microsoft SQL Server 2005 Express – up to 5 hosts and 50 VMs. If the machine has Microsoft SQL Native Client installed, remove it before
installing vCenter Server with the bundled database. If the machine has MSXML Core Services 6.0 installed, remove it before installing
o Microsoft SQL Server 2005 – Windows XP, apply MDAC 2.8 SP1 to the client. Use the SQL Native Client driver (version 9.x) for the client.
Ensure that the machine has a valid ODBC DSN entry. Remove MSXML Core Services 6.0 before
o Microsoft SQL Server 2008 – Windows XP, apply MDAC 2.8 SP1 to the client. Use the SQL Native Client driver (version 10.x) for the client.
Ensure that the machine has a valid ODBC DSN entry.
o Oracle 10g – If necessary, first apply patch 10.2.0.3 (or later) to the client and server. Then apply patch 5699495 to the client. Ensure that
the machine has a valid ODBC DSN entry.
o Oracle 11g – Ensure that the machine has a valid ODBC DSN entry.
o Even though vCenter Server is supported on 64-bit operating systems, the vCenter Server system must have a 32-bit DSN. This requirement
applies to all supported databases. By default, any DSN created on a 64-bit system is 64 bit. On a 64-bit system use
C:\WINDOWS\SYSWOW64\odbc32.exe.
o vCenter Server must have a computer name that is 15 characters or fewer. The data source name (DSN) and remote database systems can
have names with more than 15 characters.
o To prepare a SQL Server database to work with vCenter Server, you generally need to create a SQL Server database user with database
operator (DBO) rights. VCP-410 braindump
o If you use SQL Server for vCenter Server, do not use the master database.
o When using Microsoft SQL Server 2008 Standard Edition with vCenter Server, do not name the instance MSSQLSERVER.
o The vCenter Server performs a silent installation of vCenter Orchestrator. If you install vCenter Server on an IPv6 operating system, the
vCenter Orchestrator module is not supported.
o The vSphere Host Update Utility is for updating and patching ESXi 4.0 hosts and upgrading ESX 3.x/ESXi 3.5 hosts to ESX 4.0/ESXi 4.0.
o You can join multiple vCenter Server systems to form a Linked Mode group.
o Linked Mode global data includes:
o Connection information (IP and ports)
o Certificates
o Licensing information
o User roles